Exactly how to Replace a Bath Tub (Step By Step).
Exactly how to Replace a Bath Tub (Step By Step).
Blog Article
We've uncovered this great article relating to How to Install a Bathtub Yourself down the page on the web and figured it made good sense to relate it with you over here.
Setting up a tub isn't specifically rocket science, yet it does require strong plumbing, woodworking, as well as often, tiling skills. Changing an old bathtub with a brand-new one is additionally a moderately tough project. If the old tub is conveniently obtainable, the project can relocate speedily; if you have to open up a wall surface to remove the old bathtub and also position the new bath tub, the job is much harder. In either situation, the task is within a home handyman's skills, although you will certainly require an assistant to move out the old bathtub and also set in the new one. Make certain you have actually qualified yourself for the task as well as fit attempting it. Instead of working with a professional to take control of a halfway-completed project, it is much better to take into consideration employing one before you start. Chances are you may require a specialist plumber to make tube connections.
This post will certainly help you set up a brand-new bath tub in your bathroom if you have currently acquired a brand-new tub and don't require to transform the arrangement of your previous water system pipelines.
Your devices and material checklist must consist of the following:
Preparing for the Installation
Firstly, the supporting framework provided with the bathroom needs to be fitted (if needed) according to the maker's guidelines. Next off, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is important to ensure that if the tap includes a plastic washing machine, it is fitted in between the bathroom and also the faucets. On a plastic bathroom, it is additionally practical to fit a supporting plate under the taps device to stop strain on the bathtub.
Fit the flexible tap connectors to the bottom of the two taps using 2 nuts and olives (sometimes supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the electrical outlet via the hole in the bathroom. Make use of the nut provided by the supplier to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bathroom. Ensure you utilize all of the supplied washing machines.
Attach the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Connect all-time low of the overflow tube in a comparable manner.The bathroom ought to now prepare to be fitted in its last position.
Removing Old Touches
If you require to replace old faucets with brand-new ones as a part of your setup, then the first thing you ought to do is disconnect the water supply. After doing so, turn on the faucets to drain any water remaining in the system. The procedure of getting rid of the existing taps can be quite bothersome because of the restricted access that is frequently the case.
Make use of a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that links the supply pipes to the faucets. Have a fabric ready for the continuing to be water that will certainly come from the pipes. As soon as the supply pipes have actually been removed, make use of the exact same device to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the solitary taps from transforming during this procedure. When the faucets have been gotten rid of, the holes in the bath/basin will need to be cleaned of any kind of old securing compound.
Prior to moving on to fit the brand-new taps, contrast the pipeline connections on the old faucets to the new faucets. If the old faucets are longer than the new faucets, then a shank adapter is required for the brand-new taps to fit.
Mounting the Bathtub
Utilizing both wooden boards under its feet, put the bath tub in the required setting. The wood boards are valuable in equally spreading the weight of the tub over the location of the boards instead of concentrating all the weight onto 4 small factors.
The following goal is to make sure that the bath tub is leveled all round. This can be achieved by inspecting the level and changing the feet on the bath tub until the spirit level checks out degree.
To install taps, fit all-time low of the outermost flexible tap adapter to the appropriate supply pipe by making a compression join; after that do the very same for the other tap.
Turn on the water and check all joints as well as brand-new pipework for leakages and also tighten them if necessary. Fill up the tub as well as also check the overflow outlet as well as the regular electrical outlet for leaks.
Finally, repair the bathroom paneling as defined in the supplier's instruction manual. Tiling and sealing around the tub must wait up until the bath tub has actually been made use of at least once as this will settle it into its final setting.
Suitable New Touches
If the tails of the brand-new faucets are plastic, after that you will certainly require a plastic adapter to stop damages to the string. One end of the adapter fits on the plastic tail of the faucet and also the various other end provides a link to the current supply pipelines.
If you need to fit a monobloc, then you will require lowering couplers, which attaches the 10mm pipeline of the monobloc to the common 15mm supply pipe.
Next, position the faucet in the placing hole in the bath/basin guaranteeing that the washers are in area in between the tap and the sink. Secure the faucet in position with the producer provided backnut. As soon as the tap is securely in place, the supply pipelines can be attached to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with regular faucet ports. The former kind ought to be attached to the tap ends initially, tightening only by hand. The supply pipes can later be attached to the various other end. Tighten both ends with a spanner after both ends have actually been connected.
Tiling Around the Bathtub
In the area where the bathroom satisfies the tile, it is necessary to secure the joins with a silicone rubber caulking. This is important as the installation can move sufficient to split a rigid seal, creating the water to permeate the wall in between the bath and the tiling, causing problems with dampness as well as possible leakages to the ceiling below.
You can pick from a range of coloured sealants to assimilate your fixtures as well as fittings. They are marketed in tubes and cartridges, and also are capable of securing spaces approximately a width of 3mm (1/8 inch). If you have a bigger space to load, you can fill it with spins of soaked paper or soft rope. Bear in mind to always load the tub with water prior to sealing, to permit the movement experienced when the bathtub is in usage. The sealant can split rather early if you do not take into account this motion prior to sealing.
Additionally, ceramic coving or quadrant tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are additionally easily offered on the marketplace. It is recommended to fit the floor tiles using waterproof or water-proof adhesive and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We were shown that report about How to Install a Bathtub from a good friend on another web blog. Sharing is caring. Helping others is fun. I love reading our article about How to Install a Bathtub Yourself.
Get A Free Estimate Report this page